How To Remove Kitchen Faucet With U Shaped Bracket

How to remove kitchen faucet with U shaped bracket? Although sound technical, it can be possible through a DIY approach if you follow the laid down steps.

The U-shaped bracket entails the main mounting for the faucet and where the sprayer line meets. It consists of a thick black plastic piece and a thin metal bracket with what appears to be riveted in it. Beneath, you will see the whole length of the pipe threaded, and a nut is situated below the U-shaped steel bracket.

To remove a kitchen faucet with U shaped, you can use the pull-out approach to replace the whole sink just to get to replace the faucet.

In this post, I will guide you on removing kitchen faucets with U-shaped brackets.

How To Remove Kitchen Faucet With U Shaped Bracket

The following are the step-by-step approach to removing a kitchen faucet with U shaped brackets.

Step 1: Prepare the Sink

To prepare the sink entails cleaning and clearing off the dirt in the sink to prepare the sink for the removal process. When you clean the sink, the next is to use an old towel to cover the cabinet’s bottom to track in chemical residue.

Step 2: Shut off Water and Hose

After preparing the sink, the next thing to do is shut off the water. Located on the front or top of each pipe is a shutoff valve for hot or cold water. Normally, the right one is usually cold, whereas the left one is typically warm.

You just have to shut off the pipe that runs to the faucet, so carefully trace them to be double sure before shutting it off. Next, turn the knobs clockwise until fully encased to secure them.

Step 3: Loosen the Nuts

Next is to loosen the nut. Before doing that, carefully inspect the area beneath the sink for a nut where the faucet is attached. The nut usually is used to secure a U-shaped brace to the sink.

It is recommended that you use a Liquid Wrench Penetrating Oil on your hand before you loosen the nut. So using this oil makes this particular stage easier.

Step 4: Pull Out the Faucet

Once you have removed the resistant nut, the next is to pull out the faucet from the top. It is advised you take caution when you see the crumbled black foam seal (muck and filth) beneath your feet.

Using a putty knife, carefully scraped away the old foam seal glued to the sink. Afterwhich, you can use the Magic Eraser to take care of the rest.

What To Consider To Choose The Right Kitchen Faucet?

To purchase the right kitchen faucet, there are some factors you have to keep in mind. They are:

Number of Holes

Before buying a new faucet, you need to inspect your deck plate carefully. For every deck plate situated under the faucet neck, there is a possibility that there is more than one hole hidden. Knowing the exact number of holes helps to know which faucet to choose to avoid any shocking surprises during the installation process.

Type of Finishing

The type of finishes in the kitchen helps decide what type of faucet to get. For your kitchen décor to be perfect and for the kitchen to look nice, you should avoid contrasting finishes.

Look at the drawer’s and cabinet door’s handles, and pick a color and shade that matches.

Another important factor to consider while choosing is the faucet finish’s ability to resist fingerprints, stains, and water spots. Some faucet comes with a spot-resistant coating, which helps maintain the faucet’s cleanliness.

Height

Typically, a higher kitchen faucet allows enough space to keep bulkier appliances. And it aids comfortability and convenience.

Can You Remove The Kitchen Faucet Through DIY Approach?

You don’t necessarily need a plumber to remove the U-shaped faucet, as you can do it yourself if you follow the steps discussed above. Using just a basin wrench and some simple equipment, you can get the job done within an hour or so.

Getting a plumber to install a faucet can be expensive as it will cost about $150 or more.

If you have to do extra plumbing work, such as rerouting or reworking the pipes under the sink, it may cost you about $250. So it is more cost-effective to use a DIY approach.

Frequently Asked Questions (FAQs)

How do you remove a kitchen faucet mounting hardware?

Use a basin wrench to reach the sink basin from inside the vanity cabinet. Then grip the mounting nut that connects one of the faucet valve tailpieces to the sink or countertop. Next, turn the nut anti-clockwise to loosen it and unscrew it down the threaded tailpiece.

Is it possible to remove a kitchen faucet without a basin wrench?

Removing a kitchen faucet without a basin wrench following the laid-down steps is very much possible.

  • Step #1: Shut Off Valves & Turn Out the Water Supply Lines
  • Step #2: Open the Spigot
  • Step #3: Turn Off the Water Piping.
  • Step #4: Unscrew and Pull Out The Faucet Mounting Nuts or Screws
  • Step #5: Disconnect and Pull Out the Hose

How do you remove faucet clips?

The steps below show the gradual procedure to remove the faucet clips.

  • Shut off the water ( hot and cold water) supply lines completely that are located underneath the sink.
  • Keep a bucket underneath the faucet connections.
  • Turn on the faucet to allow for the easy release of water pressure in the faucet.
  • Twist the Metal Clip anti-clockwise by hand to release it.

What is a basin wrench?

A basin wrench is a wrench with a long shaft that contains pair of asymmetrical jaws arranged at one end and the other end a transverse handle. The two jaws form a union in which the jaws are joined together with a pivot pin.

What can you use instead of a basin wrench?

Instead of using a basin wrench to loosen nuts and bolts, you can go for Zip Tie or cable fasteners, as they are often used as an alternative to basin wrenches because of the numerous advantages they offer, such as being much easier to use on the hands while working and they posses small fasteners like Allen key screws.

How do you remove a stuck faucet stem?

You can use a WD-40 to remove a stuck faucet stem. All you have to do is spray the lubricant on it to penetrate the valve stem and cartridge as possible completely. Let it lie for some minutes, after which you can try removing the cartridge.

How do you remove a mounting nut?

To remove a mounting nut, you must first position the flathead screwdriver against one of the plastic nibs. Then use a hammer to fasten the end of the screwdriver to loosen the nut. It might be somehow difficult to get a good angle with the screwdriver, but with full concentration, you should be able to get one. However, you can also maneuver it in a perpendicular way to the washer, which also helps to loosen the nut.

Is it possible to remove a faucet aerator without tools?

Yes, it is. You can unscrew it with your bare fingers if the aerator hasn’t been used for a long time. All you have to do is find a rubber glove or cloth to give you more grip to twist the aerator to loosen and unscrew it. If your fingernails are strong, you can use them.

Conclusion

To remove kitchen faucet with U shaped bracket does not require many technicalities as you have first to remove the quick connect; in some faucets, it is double.

To disconnect the quick connection on your hose, you just have to squeeze on both white buttons on either side of it.

You gradually pinch, wiggle, and pull down the U bracket to remove it upon removing the bolt.

Immediately you do that; you can easily pull out the old faucet.

I hope you loved and found this article interesting. For more related posts, do check out, “How To Remove Kohler Kitchen Faucet.”

 

Leave a Comment