About three of them are Moen faucets for every five cartridge faucet homes. Moen is regarded as a trusted U.S-based brand known for its quality and reliability in terms of kitchen faucets. Still, the faucets can break or get old, and you want to remove and replace them either singularly or during a total kitchen remodeling.
Faucets are easy to remove most times, but they are formulaic. Each has its unique removal process. Or else, it can lead to damages or further leakages or breakage to the faucet.
So in this article, we will be showing you how to remove Moen kitchen faucet without causing any further damage to the faucet.
How To Remove Moen Kitchen Faucet Like A Pro
When removing Moen kitchen faucets, you don’t need many tools. You just need a few basic tools, and you can do it yourself.
The tools you need are:
- Needle nose pliers, and
- A wrench.
Below are the formulaic steps you have to follow to replace Meon kitchen faucet successfully.
Step 1: Close The Waterline Valve
Before starting the removal process, the first thing you have to do is find the water line supply and close the valve. Most modern homes have separate valves for cold and hot water, so ensure you close both.
Step 2: Empty The Pipes
After shutting down the water valve, the next step is to empty the pipes. To do that, open the sink valve to check for any left-out water in the pipe and drain them off. If you don’t do this, you risk water draining into your cabinets or onto your floor, which will cause a mess in the kitchen.
Step 3: Unscrew The Faucet’s Handle
Use a screwdriver to remove the faucet’s handle. Once you have successfully removed it, check out the set screw. Once you find it, use the wrench to unscrew it and take off the handle carefully and gradually.
Step 4: Remove The Plastic Part
After removing the faucet’s handle, the next thing you should do is to check whether there is a major leak, a malfunctioning rubber gasket, or any form of abnormality. When you find a small dome and a jacket, you must pull out with a wrench. Insert the wrench and turn it, and the parts will slowly slide out.
Step 5: Remove The Mechanism
Once you are done removing the plastic sleeve, next is to take out the handle mechanism. The handle mechanism controls the waterline flow, so you have to be careful to avoid damaging it.
There is a screw that connects the mechanism to the sink. All you have to do is use a screwdriver to loosen the screw and then pull out the mechanism.
Step 6: Remove The White Ring
Once you’ve taken off the mechanism, you can now remove the white ring under it. When removing the white ring, do ensure to keep it in a safe place as you will need it to set up a new faucet. Also, there is a washer under the ring that you will need to remove.
Step 7: Remove The Spout
If you carefully go through the steps, you’ll have no difficulty taking out and removing the spout. After you have removed the sprout, you need to document all the previous steps to go through them, fixing a new faucet back.
If you do the previous steps rightly, the spout part will easily come out without any tools. Next, you will find a clip under the spout. Then, using a screwdriver, take off the clip using. If the old faucet is still intact, you’ll also need to take off the cartridge. Using pliers to hold the stem, spin the faucet until it loosens. If pliers can’t help, you can utilize the cartridge puller.
After you are done with the whole removal process, assess the condition of the faucet, and prepare for your Moen faucet repair. For Kitchen faucet repair, you will need the same set of tools for replacing.
If you could replace yours successfully, that shows that you can also successfully put it back.
Reinstalling Moen Kitchen Faucet
After removing the Moen kitchen faucet, it is necessary that you carefully inspect it for possible damages, linkages, or faults. If you notice any, you may have to replace the valve.
Once you have gotten the necessary parts, you can begin the reinstalling process. So that shouldn’t be a problem; however, I will show you the steps required to reinstall.
Steps Involved In Installing A Moen Kitchen Faucet
Installing new Moen kitchen faucets is as straightforward as removing them. All you have to do is follow the steps carefully, and you are good to go.
First, place the plastic gasket, rubber cap, or trim ring on the empty hole in the sink. You must consult the manufacturer’s manual or handbook for instructions and guidelines concerning the installation. If you don’t have experience installing faucets and are good at learning visually, I recommend you watch a YouTube video on it.
You can turn the video on and follow their guide. Once you finish, you can proceed to the next stage, positioning the faucet handle into the sinkhole. Then Install washers under the sink, after which you pause for the area to carefully dry. Next, attach the sprayer hose to the main supply pipe.
Pull down the hose, and add the weight. Remember that the weight needs enough space to hang freely. Next, connect the water supply lines and secure them using the plumber’s tape.
It is important for you never to tighten the supply lines as they may burst and cause damage to your sink. Next, turn the water and watch out for any form of abnormity. If you don’t notice any, you can take off the aerator and open up the valve to clear the lines. Then you are done.
Reinstalling faucets can seem difficult to many people, especially if this is your first time doing it. With these above simple steps, you can easily fix the damage in your bathroom, home office sink, or living room.
However, suppose the whole process of removing, replacing, and installing Meon kitchen faucets seems to be a complex project to you. In that case, you can also call a professional plumber to help out. However, it will require you to increase your budget.
Frequently Asked Questions (FAQs)
How Do You Remove A Moen Single Handle Kitchen Faucet?
Most times, a Moen single-handle kitchen faucet can be removed by loosening the screw in the back of the handle. Use a 3/32” hex wrench to loosen the screw. After removing the handle, carefully unscrew the spout collar nut by turning anticlockwise, next lift and rotate the spout.
How Do You Remove A Moen Kitchen Faucet Handle Without Screws?
You may ask if it is possible to remove a Moen kitchen faucet without screws. It is very much possible. You can use an Allen wrench (also called an Allen key) to make it happen. After that, lift the faucet handle off. If it has a cartridge inside, it will require you to unscrew a top piece, including removing the cartridge.
How Do You Remove A Screwless Faucet Handle?
All you have to do is get the required tools, after which you carefully follow the below steps to remove the screwless faucet handle successfully.
- Step 1: Turn off the water.
- Step 2: Take off the cap on top of your faucet
- Step 3: Take off the hidden set crew
- Step 4: Take off the faucet handle
- Step 5: Wash out the mineral deposits
How Do You Remove The Handle On A Moen Bathroom Faucet?
The first thing you have to do is remove the Hardware on the backside of the faucet body; there, you will find the Allen screw. Then you use an Allen wrench to remove the screw. If the Hardware remains strong and refuses to loosen, you may have to use penetrating oil to help loosen them. Once you have successfully removed the Allen screws, you can lift the faucet body and remove its base.
How Do You Clean A Moen Faucet?
You can easily use a damp cloth and mild liquid dishwashing soap to clean a Moen faucet, after which you rinse it out with water and dry it with a soft cloth. Also, you can go for common household cleaners such as mild abrasives for Brushed Chrome and Platinum. However, ensure you stick to the manufacturer’s guide when using certain products on a Moen kitchen faucet.
You can easily replace, repair, and install the Moen Kitchen faucet if you carefully follow the above-laid down steps. Note that there aren’t shortcuts to it, and trying to skip a degree can lead to damage which can be messy.